Resources for Science Olympiad Flight Students
NFFS partners with Science Olympiad to sponsor and support the Indoor Flying Events for the B and C divisions.
2026–2027 Flight Rules coming soon!
Resources for coaches and Event Supervisors can be found here.
Getting Started
- Indoor Free Flight Airplane Glossary
- Design Overview, Kit Selection and Key Factors for Success – a quick overview for students who are new to the airplane event.
Building
- Glue and Glue Management for Indoor Models (Video) – Make your airplanes strong, and avoid unnecessary weight.
- Wing and Box Trimming (Video) – What to do if your plane/glider/helicopter doesn’t fit into the box, or if your box is slightly too large. This video pertains directly to airplanes, but is generally applicable to gliders and helicopters if you have a box problem.
- Covering (Video) – Demonstration of covering with Ultrafilm. Shows covering techniques for airplanes.
- Super simple airplane build video – Full construction video of a super simple Wright Stuff airplane. Half an hour to build and two minute flights; cost only $15. Shows an airplane from 2023-24, so you MUST read video comments for 2026-27 dimensional changes to wing, fuselage, tailboom, etc.
- Super Simple airplane flying over two minutes
- Make a Simple, Cheap, Torque Meter (video) – Built from free paint stir sticks and a guitar string. Costs as little as one dollar and takes only 30 minutes to construct. Winding with a torque meter is critical to success in the flying events. See this related PDF document.
- Balsa Density Calculator – Very handy for building to identify wood density for each part in order to keep the model down to minimum weight.
Flying
- Airplane Flying – A Simple Approach – A beginners guide to rubber selection and winding. Improve your winding technique, no torque meter required! New for 2026/27, includes winding video.
- Next Level Airplane Flying – A more sophisticated approach, with advanced winding and rubber management techniques, which will enable you to push your airplane flights to new heights!
- Winding without a Torque Meter – This document references the video below, with details that you should change if you are winding without a torque meter. Includes a step by step set of instructions that you can print and take with you to the gym.
- Winding with a Torque Meter (Video) – Winding a rubber motor to max torque and then backing off to launch torque for effective utilization of rubber.
- Max Turns Calculator – Live calculator for estimate of max rubber turns before breaking based on rubber dimensions.
- Rubber Tying for Indoor Duration Model Airplanes (Video) – Tie rubber motors to exact mass, reduce chance of knot slipping.
- Basic Rubber Management for SO Flight – Successful flyers take into account many variables when selecting, tying, winding, and managing their motors. This document outlines basic techniques to help improve your approach to rubber motor management, which will also aid in improving your flight consistency.
- Basic Airplane Data Log Template – A basic flight log with many parameters that will help to document and improve your flying. Includes a detailed description of log parameters, why and how they are measured, and how they are used to improve your flying.
Advanced and Additional Topics
- A Guide to SO Planes by Chuck Markos – An excellent introduction
- Trimming Reference – This document discusses the hows and whys of vertical trim, stability, and circular flight path. For a step-by-step guide to trimming an airplane, see the trimming resources below.
- Indoor Free Flight Glossary
- Prop Pitch / Rubber Motor Balance (Video) – Optimize the propeller pitch to the rubber cross section for maximum efficiency.
- Prop Building for Rubber Powered Indoor Airplane Models (Video) – Build your own props, demo with small Scraps prop.
- Aircraft Forces, Moments, and Stability – Aerodynamic principles and discussion of airplane stability
- Bucket Prop – Forming prop blades on a cone or cylinder, Search for “bucket” in the HPA library
- Making a Wire Pigtail Thrust Bearing (video) – How to form one out of wire as an alternative to using pre-made aluminum or plastic prop hangers.
- Wright Stuff Paper – A comprehensive guide to SO planes, written by former competitor Patrick Schwartz.
Getting Started
- Wondering How to Get Started with Gliders? Read This First! – An overview to get you going.
- Glider Basics (Video) Look at this next! – glider designs, kits manufacturer links & keys to success.
- Indoor Free Flight Glider Glossary – Terms utilized in construction, initial flying, trimming, and optimizing flight characteristics. Definitions with an explanation of the impact each has on the flight of a glider.
Building
- Building Tips for a Basic (non-flapper) Glider – Pertains to a glider with an all balsa wing, without foam flaps.
- Building Tips for a Flapper Glider – Some additional building considerations for a flapper.
- Balsa Density Calculator – Very handy for building to identify wood density for each part in order to keep the model down to minimum weight.
Flying
- Launching and Trimming a Basic (non-flapper) Glider – How to get your glider flying without breaking it. Read this before you launch your glider!
- Launching and Trimming a Flapper Glider – Significantly different techniques for a flapper as compared to a basic glider.
- Basic Glider Data Log Example – A sample log with each of the parameters explained – why do you want to record that parameter, how do you measure it, and what units does it have? Here is an Excel spreadsheet template you can use.
Advanced and Additional Topics
- Advanced Trimming Techniques for a Flapper Glider – Take your flying to the next level! (Only do this after following the advice in the Launching and Trimming resource above.)
Here are some things to consider when selecting a kit, or if planning to build from scratch, construction tips, and rules related discussions to help you in the process of building a helicopter. Great information from a variety of experienced sources.
- Wondering How to Get Started with Helicopters? Read This First! – An overview to get you going.
- Helicopter Basics (Video) Look at this next! – Another introduction that discusses different helicopter designs, with some additional information about rubber management.
- Indoor Free Flight Helicopter Glossary – Terms utilized in construction, initial flying, trimming, and optimizing flight characteristics. Definitions with an explanation of the impact each has on the flight of a helicopter
- Balsa Density Calculator – Very handy for building to identify wood density for each part in order to keep the model down to minimum weight.
You’ve finished building, and are eager to start flying. It is pretty easy to be successful, but equally easy to end up frustrated, if you don’t know what to do. Take a look at these resources, that will guide you through the process of getting your bird up into the air!
- Helicopter Flying: A Simple Approach – A beginners guide to rubber selection and winding, the most important contributors to long helicopter flights. Improve your winding technique, no torque meter required! New for 2025/26, includes winding video.
- A Road Map for Your Helicopter Journey – Step by step helicopter flight improvement guide by Areo Martin
Next Level Helicopter Flying – A more sophisticated approach, with advanced rubber management techniques, which will enable you to push your helicopter flights to new heights!
- Winding and Launching A Science Olympiad Helicopter (Video) – Winding for Helicopters is mostly like winding for airplanes, with some important differences. Learn how to do it from this video, which also includes some launching tips.
- How Not to Kill Your Winder
- Make a Simple, Cheap, Torque Meter (video) – Built from free paint stir sticks and a guitar string. Costs as little as one dollar and takes only 30 minutes to construct. Winding with a torque meter is critical to success in the flying events. See this related PDF document.
- Max Turns Calculator – Live calculator for estimate of max rubber turns before breaking based on rubber dimensions.
- Rubber Tying for Indoor Duration Model Airplanes (Video) – Tie rubber motors to exact mass without slipping
- Basic Helicopter Data Log Example – A sample log with each of the parameters explained – why do you want to record that parameter, how do you measure it, and what units does it have? Here is an Excel spreadsheet template you can use.
Advanced Topics
Let’s say you have your helicopters flying consistently well. Or, you want to incorporate advanced building techniques into your helicopter. Here are some things you can try in order to add a few more seconds to your flight times, or to scratch build your own helicopter or modify your kit.
- How to adjust the rotor pitch (2025–2026)
- Example Flight Log – A very complete flight log with many parameters that will help to document and improve your flying.
- Making a Wire Pigtail Thrust Bearing (video) – How to form one out of wire as an alternative to using pre-made aluminum or plastic prop hangers.
A collection of videos that support SO Flying events and other helpful NFFS free flight videos can be found on this page –
https://www.youtube.com/c/NationalFreeFlightSociety
A collection of good stuff from a wide variety of sources. There is something here that will help your flying, regardless of your current level of expertise.
Science Olympiad Student Center Forum – Ask questions, discuss problems, connect with students and experienced coaches. Navigate to Build Events, then Flight.
Kits
Laser Cut Planes – Simple build, interlocking assembly
Freedom Flight Models – Advanced kits, excellent build manuals, many materials incl. custom cut rubber
J&H Aerospace – Excellent kits, manuals, and online videos. Many parts and tools as well
Retro RC – choose “Scholastic Kits and Accessories” from menu
Guru Engineering Tech – Planes from a winning coach
Ward Scientific – A basic kit including a plan, wood, covering, tools
Helicopter Plans
2025 NFFS Plan – A simple, full-size (11×17), plan by Dave Aronstein, uses a minimum of different balsa stock.
River City Rocket – A simple X-rotor design from 2011, modify diameter to fit box.
Jim Richmond’s AMA Design – A complex 0.373g heli for ideas. From Winning Indoor Designs 2002–2005.
Bill Silin’s AMA Design – A complex 0.835g heli, for ideas
Tools, Rubber, etc.
Indoor Free Flight Supply – Basic and advanced tools for building and flying, rubber
FAI Model Supply – Stock rubber sizes in bulk, Ikara props, other parts
Indoor Specialties – Tools, prop hangers, covering. Currently closed for Covid, but has some resource articles available
Miscellaneous
3D Printing for Science Olympiad Events
Coaches’ Clinic – A presentation that reviews the Helicopter event, changes from last year, and tips and tricks.

